TL;DR (What causes most failures)

• Energy mismatch: daily load (Wh/night) is higher than the real charging yield (worst-month), causing long-term low SOC and early shutoff.
• Ingress and corrosion: sealing inconsistency, cable glands, connectors, and humidity cycling create intermittent faults.
• Installation & commissioning: PV shading/tilt mistakes, incorrect dimming settings, missing commissioning records, loose hardware.
• Maintenance gaps: soiling, damaged cables, loose fasteners, and ignored early warning symptoms.
• Vandal/theft: hardware not specified, installation evidence not required, poor mounting strategy.

Mulakan di sini (dalaman):

• Pengiraan Hari Autonomi
• Rainy Season Sizing (Worst-month method)
• Pemilihan IP & IK
• Senarai Semak Pemasangan & Pengkomisionan

Failure Mode 1: Early shutoff or reduced runtime

Symptoms

• Lights turn off before dawn or after a few hours
• Runtime declines over weeks after installation

Common root causes

• Undersized PV/battery for worst-month conditions
• Dimming profile not disclosed (real Wavg higher than assumed)
• PV shading, wrong tilt/orientation, heavy soiling
• Battery usable energy assumptions unrealistic

Prevention (procurement controls)

• Perlukan satu lembaran belanjawan tenaga (Wavg, hours, Wh/night)
• Memerlukan worst-month PV yield sanity check with disclosed assumptions
• Require commissioning record of dimming mode

Panduan berkaitan:

• Pengiraan Hari Autonomi
• Saiz Musim Hujan
• PIR vs Penggelapan Masa

Failure Mode 2: Water ingress / moisture-related faults (intermittent)

Symptoms

• Random on/off behavior after rain
• Condensation inside lens area
• Corroded connectors, green/white oxidation, rusted fasteners

Common root causes

• Sealing inconsistency (gaskets, glands, vents)
• Improper cable gland assembly, over/under torque
• Humidity cycling + poor venting strategy
• Coastal corrosion not addressed (IP alone does not solve corrosion)

Prevention (procurement controls)

• Specify IP target based on environment AND request sealing evidence (photos + QC checklist items)
• For coastal/humid: require a corrosion strategy statement (hardware/coating/connectors)
• Require installation photo checklist to verify glands/cable routing

Berkaitan:

• Pemilihan IP & IK
• Pusat Bukti Kualiti dan Pengujian
• Pelan penyelenggaraan

Failure Mode 3: Battery degradation / low usable capacity

Symptoms

• Autonomy drops earlier than expected
• System enters protection mode more often

Common root causes

• High temperature stress, deep cycling, chronic low SOC
• Undersizing causes extended low SOC during cloudy weeks
• BMS protection thresholds frequently triggered due to poor sizing

Prevention (procurement controls)

• Perlu dinyatakan usable factor and assumptions in sizing
• Require worst-month recharge check (avoid “SOC walk-down”)
• Require warranty scope by component (battery + BMS)

Berkaitan:

• Tempoh hayat bateri LiFePO4
• Syarat Jaminan

Failure Mode 4: Controller issues (charging/lighting logic)

Symptoms

• No charging indication even in sunlight
• Wrong dimming behavior vs what was promised
• Night mode not triggered correctly

Common root causes

• Incorrect configuration or missing commissioning process
• Mismatch between controller logic and autonomy calculation assumptions
• Low-quality wiring/connector issues causing voltage drop

Prevention (procurement controls)

• Require a declared dimming profile and commissioning record (mode + settings)
• Require protections list and configuration verification steps

Berkaitan:

• Pengawal MPPT vs PWM
• Senarai Semak Pemasangan & Pengkomisionan

Failure Mode 5: PV underperformance (charging deficit)

Symptoms

• System works for a few weeks then runtime declines
• Battery never reaches full charge

Common root causes

• Shading (trees/buildings), wrong orientation/tilt
• Dust/soiling not included in maintenance plan
• PV Wp is insufficient for worst-month PSH assumptions

Prevention (procurement controls)

• Require site installation photos (shading check + orientation)
• Require worst-month PV yield sanity check and maintenance plan

Berkaitan:

• Monokristal vs Polikristal
• Pelan penyelenggaraan

Failure Mode 6: Thermal stress and lumen depreciation

Symptoms

• Brightness noticeably drops over time
• LED failures or driver issues increase at high ambient temperatures

Common root causes

• Insufficient heat path / heat dissipation design
• High sustained power without proper thermal strategy

Prevention (procurement controls)

• Require a thermal management explanation and consistent configuration control
• Ensure autonomy and dimming assumptions avoid unnecessary high sustained load

Berkaitan:

• Pengurusan Terma & Pengurangan Lumen

Failure Mode 7: Wiring/connectors corrosion and loose connections

Symptoms

• Intermittent operation, flicker, random resets
• Charging works sometimes, fails other times

Common root causes

• Connector oxidation/corrosion (coastal/humid environments)
• Poor strain relief, cable rubbing damage
• Loose terminals from vibration and inadequate torque control

Prevention (procurement controls)

• Require connector protection method in corrosion strategy
• Require installation photo checklist showing cable routing and strain relief

Berkaitan:

• Bukti Kualiti & Pengujian
• Senarai Semak Pemasangan & Pengkomisionan

Failure Mode 8: Theft/vandal incidents

Symptoms

• Missing PV modules, battery packs, or luminaire heads
• Damaged lens/housing from impact

Prevention (procurement controls)

• Specify anti-tamper hardware and mounting strategy (anti-theft ≠ IK)
• Require serial-to-location mapping and installation photos for enforcement and warranty

Berkaitan:

• Pilihan Anti-Curi
• Pemilihan IP & IK

Field troubleshooting path (safe, practical)

Safety note: if the system requires opening electrical compartments, use qualified technicians and follow local safety procedures.

1. Confirm configuration: check commissioning record (mode + dimming profile). If missing, treat as incomplete handover.
2. Check PV shading/soiling: confirm orientation, tilt, and visible shading; inspect for heavy dust/film.
3. Check connectors and cable damage: look for corrosion, loose connectors, rubbing, and exposed conductors.
4. Check pattern: fails after rain? suspect ingress/condensation. Fails after cloudy weeks? suspect energy mismatch/worst-month deficit.
5. Document evidence: photos/video + serial number + location + settings record (needed for warranty).

Use these operational pages for handover and prevention:

• Senarai Semak Pemasangan & Pengkomisionan
• Pelan penyelenggaraan
• Syarat Jaminan

Procurement PASS/FAIL rules (make failures less likely)

Menandakan bidaan GAGAL (Tidak Boleh Dibandingkan) jika ia kekurangan:

• Lembaran belanjawan tenaga (Wavg, jam masa operasi, Wh/malam)
• Worst-month PV yield sanity check (disclosed assumptions)
• IP/IK evidence package (not just a brochure line)
• Commissioning settings record template (handover requirement)
• Warranty workflow (scope + SLA + evidence list)

Request Failure Diagnosis & Prevention Pack

Get the editable package used for operations and warranty claims:

• Failure modes checklist (symptoms → causes → actions)
• Installation photo checklist + serial-to-location mapping template
• Sempadan rekod komisioning (mod + tetapan)
• Preventive maintenance schedule (inspection points)
• Senarai semak bukti tuntutan waranti

Soalan Lazim

What is the #1 cause of early shutoff?

Energy mismatch: daily load (Wh/night) is higher than real charging yield during worst-month conditions, causing long-term low SOC and early shutoff.

Why do some failures appear only after rain?

Moisture/ingress issues often create intermittent faults: condensation, corrosion, and leakage paths that show up after wet weather.

What evidence helps the most in warranty claims?

Serial number, installation photos, commissioning settings record, and clear documentation of the failure pattern (after rain vs after cloudy weeks).